Console (DSM) (CPM)(SRM) V6.57  (Date Code Fri May  3 15:41:40 PDT 2019)

1.	OpenSSL: 1.0.2r-fips  26 Feb 2019 (update)
2.	Openssh: 8.0p1 (update)
3.	Apache httpd: 2.4.39 (update)
4.	RESTful Versions: v1.0, v2 (Jan19) (update)
5.	Added option to update the firmware via web
6.	Add IPSEC VPN Server option
7.	Ansible Support
8.	Add failed Ethernet interface to Wake up on failure alarm message.
9.	Add DHCP Client and Server option
10.	Added Fallback the network traffic/ Resilient gateway opton  
11.	Added Cell usepeerdns on/off parameter
12.	Auto close upgrade process after 30 mins (turn off FTP/SFTP) Mario request
13.	Syslog Port assignment, outgoing and incoming (Splunk request) update menu system
14.	Update Certificate chain
15.	Default serial port handshake to NONE instead of HARDWARE (Except internal modem)
16.	Added Buffer filtering Alarm (Push data)
17.	Changed the serial port config screen to have tabs, similar to how the CLI is separated
18.	Changed the tab names with “Configure Plugs Access” to “Select Plugs” on any screens that are not actually configuring access to the plugs (PNA, Sched Reboot, and Loadshedding) (WEB only)
19.	Modified the serial configuration screen (WEB) to put PPP parameters on a separate tab, and make this new tab the last tab.
20.	Added a ping test to the PNA and scheduled reboot screens, where we add the ip addresses
21.	Added the ability to retrieve software version number via SNMP. New MIBS that support this query were created.
22.	Added a mod to detect if a user uploaded an incorrect MD5 file, cancel the upgrade and close the ftp servers if this happens
23.	Added Firmware upgrade option via web interface



Obtaining Firmware Updates:

The most recent updates for our Console Server Products, Switched PDU Products and Data Fallback Switch products can be by filling out the firmware request form that can be found at the following page on the WTI website:

http://www.wti.com/t-firmware-upgrade.aspx

Release notes for our most recent firmware updates are listed below.

For older firmware updates, please contact WTI Tech Support at service@wti.com or call our toll free service line at 1-888-280-7227.  Customer Service Department hours are 8 AM through 5 PM, Pacific Daylight Time.



Installation:

The WMU Enterprise Management Software, which is included with WTI Devices, is the preferred method for installing firmware updates on WTI devices.  The WMU software allows you to manage firmware updates for multiple WTI units from a single interface. 

For a description of the process for managing firmware updates via the WMU, please refer to the WMU user's guide, which can be downloaded from the WTI User's Guide Archive at:

http://www.wti.com/t-product-manuals.aspx

Note that in order to use the WMU software, the existing firmware version for the WTI Device(s) must conform to the following standards:

•	Console Server Products (DSM Series, TSM Series and RSM Series):  Firmware Version v6.23 or higher.  
•	Switched PDU Products (VMR Series, NBB Series, NPS Series, RPC Series, CMM Series):  Firmware Version 1.48 or higher.
•	Data Fallback Switch Products (AFS Series):  Firmware Version 2.30

When upgrading older units that are running firmware versions that are earlier than the standards listed above, it is recommended to use the WTI Firmware Upgrade Utility.  A zip file that contains the installation files and other documentation for the WTI Firmware Upgrade Utility can be downloaded from WTI's FTP server, located at:

ftp://wtiftp.wti.com/pub/TechSupport/Firmware/Upgrade_Utility/

Please refer to the documentation included in the zip file for further instructions.

In addition to the WMU and WTI Firmware Upgrade Utility, the /UF command can also be used to install firmware upgrades.  For more information on the /UF command, please refer to the user’s guide for your WTI device.