ARM Console V8.09 (Mon Oct 13 13:09:44 PDT 2025)
1.	OpenSSL:    3.0.17 1 Jul 2025 (Library: OpenSSL 3.0.17 1 Jul 2025)
2.	OpenSSH:    10.0p2
3.	OpenVPN:    2.6.14
4.	Apache:     2.4.65
5.	Bash:       5.0.0(1)-release
6.	RESTful:    v1.0, v2 (Jul25)
7.	IPSec:      5.9.14/K5.4.0
8.	NET-SNMP:   5.9.1
9.	Restriction added to WEB & CLI to only allow for one section of an authentication protocol at a time (Radius/LDAP/TACACS)
10.	Number of Syslog client’s entries has increased to 8
11.	Cell logs/ PPP logs are now available from the Web
12.	Incremental upgrade via API
13.	Display the Warning on CLI and Web if default username/password exists
14.	SNMPv3 user can be deleted from the Web.
15.	Full Recovery option added to "/i" menu. (SSH Keys, Configuration, VPN)
16.	 Product status (/j*) now shows the clock.
17.	Allow for the creation of a local user with a $ sign (e.g., user$123) via CLI/Web.
18.	Radius/TACACS/LDAP parameters cannot be changed from Web when disabled.
19.	Fixed issue where Radius duo + OCSP Stapling being used together could cause the web server become unresponsive.
20.	IPSec VPN:
	a. %cell – Loopback address needs to be defined on web access for cell to access loopback address via HTTPS. If it’s defined under eth0 then only HTTP would work.
	b. %any – HTTPS for loopback address would only work for the interface where loopback address is defined. For example, if loopback address is defined for cell then HTTPS will not work when VPN tunnel created over the eth0 interface.
21.	2 Stop bit set to default for port settings


Obtaining Firmware Updates:

The most recent updates for our Console Server, Switched PDU and Data Fallback products can be found by visiting https://www.wti.com/pages/software

For older firmware updates, please contact WTI Tech Support at service@wti.com, call our toll free service line at 1-888-280-7227, live chat or fill out a software request form at https://www.wti.com/pages/software

Customer Service Department hours are 8 AM through 5 PM, Pacific Daylight Time.



Installation:

NetReach Centralized Management Software (NetReach), is the preferred method for installing firmware updates on WTI devices.  The NetReach software allows you to manage firmware updates for multiple WTI units from a single interface. 

For a description of the process for managing firmware updates via the NetReach, please refer to the NetReach user's guide, which can be downloaded from the WTI User's Guide Archive at:

https://www.wti.com/pages/manuals-documentation

Note that in order to use the NetReach software, the existing firmware version for the WTI Device(s) must conform to the following standards:

•	Console Server Products (DSM, CPM, and REM Series):  Firmware Version 7.04 or higher.  
•	Switched PDU Products (VMR, NBB, NPS and RPC):  Firmware Version 3.03 or higher.

When upgrading older units that are running firmware versions that are earlier than the standards listed above, it is recommended to use the WTI Centralized Management Software (WMU).  The WMU can be downloaded from WTI's FTP server, located at:

https://www.wti.com/products/wmu-centralized-management-software

Please refer to the WMU user's guide for further instructions.

In addition to the NetReach and WMU, the /UF command can also be used to install firmware upgrades.  For more information on the /UF command, please refer to the user’s guide for your WTI device.